Oil and Grit Separator

Overview

Oil and Grit Separators (OGS) are Manufactured Treatment Devices (MTDs) used for water quality treatment of stormwater runoff through the removal of large particle suspended solids and associated pollutants, and debris. Some devices can also trap light liquids such as oil and other floatables. These MTDs are typically installed underground within the stormwater sewer system in an on-line or off-line configuration. They are distinguished from Filtration-based MTDs by their removal of solids through settling rather than filtration.

Application

Oil and Grit Separators are suitable as pre-treatment to other downstream treatment systems such as ponds or LID features. Cost effective application of OGS for LID typically requires that the practice have a single inlet with a drainage area larger than 0.2 ha.

OGS normally require maintenance every year to function as designed. The cost and level of effort required to undertake the maintenance program over the full life cycle of the practice should be carefully considered when implementing this water quality treatment solution.

Testing and Verification

Several agencies across Canada require ISO 14034 Environmental Technology Verification (ETV) as a condition of technology acceptance. For OGS, the ISO 14034 verification process in Canada consists of two parts:

1. Third party laboratory testing of MTDs in accordance with the TRCA’s Procedure for Laboratory Testing of Oil Grit Separators and associated bulletins, and
2. Third party verification of the test in accordance with the 14034 ETV standard.

The ISO 14034 verification process is currently administered by Globe Performance Solutions and Verify Global. Completed ISO 14034 verification statements for OGS are posted to the former Canadian ETV website, here.

Note that ISO 14034 verification is a necessary, but not sufficient condition for approval agencies using the ISO/ETV process for technology acceptance. The technology must also be classified as an Oil Grit Separator (i.e. not include a filter) for the Procedure for Laboratory Testing of OGS to have been properly applied. This ETV Bulletin helps to provide clarification on this requirement: See table below for a list of current ISO 14034 verified OGS MTDs.

List of OGS MTDs

Verification Year (Initial)	Technology Name	Company Name	Fact Sheet
2022	RWM-DM-1200 & DM-1200-OS Stormwater Systems	Rainwater Management LTD.	Fact Sheet
2019	Hydro International Downstream Defender® OGS	Hydro International	Fact Sheet
2019	SciCLONE™ Hydrodynamic Separator	Bio Clean Environmental Inc. (A Forterra Company)	Fact Sheet
2018	Hydro International First Defense® OGS	Hydro International	Fact Sheet
2018	Hydroworks® HydroStorm (HS) OGS	HydroWorks, LLC	Fact Sheet
2017	Stormceptor® EF and EFO Oil-Grit Separators	Imbrium Systems, Inc.,	Fact Sheet
2017	CDS Hydrodynamic Separator®	CONTECH Engineered Solutions LLC	Fact Sheet
2016	SDD3 Oil Grit Separator®	Next Stormwater Solutions (8091200 Canada Inc.)	Fact Sheet

Systems designed to remove trash, debris and some amount of sediment, oil and grease from stormwater runoff based on the principles of sedimentation for the grit and phase separation for the oil.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

The technique of removing pollutants from runoff as it infiltrates through the soil.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

The total surface area upstream of a point on a stream that drains toward that point. Not to be confused with watershed. The drainage area may include one or more watersheds.