Difference between revisions of "Level spreaders"

From LID SWM Planning and Design Guide
Jump to navigation Jump to search
 
(4 intermediate revisions by one other user not shown)
Line 2: Line 2:
 
[[File:Level spreader diagram.jpg|thumb|Diagram from Wikimedia commons. Credit: U.S. Army Corps of Engineers, Construction Engineering Research Laboratory]]
 
[[File:Level spreader diagram.jpg|thumb|Diagram from Wikimedia commons. Credit: U.S. Army Corps of Engineers, Construction Engineering Research Laboratory]]
  
Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as [[vegetated filter strips]], [[swales]] or forested conservation areas<ref>Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.</ref>.
+
Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as [[vegetated filter strips]], [[Bioretention|bioretention]], [[swales]] or forested conservation areas<ref>Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.</ref>.
  
The length of the level spreader should be determined by the type of filter area and the design flow:
+
The length of the level spreader should be determined by the design storm inflow rate and type of landscape downstream:
* 1.4 m of level spreader length per every 0.01 m³/s of inflow for discharges to a [[vegetated filter strips|vegetated filter strip]] or grassed area;
+
* 1.4 m of level spreader length per every 0.01 m³/s of inflow when draining to a [[vegetated filter strips|vegetated filter strip]], [[Bioretention| bioretention]], [[Swale| swale]] or grassed area;
* 4.3 m of level spreader length per every 0.01 m³/s of inflow when the spreader discharges to a forested conservation area.
+
* 4.3 m of level spreader length per every 0.01 m³/s of inflow when draining to a forested conservation area.
 
* The minimum level spreader length is 4 m and the maximum is 40 m.
 
* The minimum level spreader length is 4 m and the maximum is 40 m.
* The level spreader lip should be concrete, wood or pre-fabricated metal, with a well anchored footer, or other accepted rigid, non-erodible material.
+
* The level spreader lip should be concrete, wood or pre-fabricated metal.
* The ends of the level spreader section should be tied back into the slope to avoid [[overflow]] scouring or erosion around the ends of the spreader.
+
* The ends of the level spreader section should be tied back into the slope to avoid [[overflow]] scouring or erosion around the ends.
* Where relevant, the width of the level spreader channel on the up-stream side of the level lip should be three times the diameter of the inflow pipe, and the depth should be 20 cm or one-half the culvert diameter, whichever is greater.
+
* The width of the level spreader should be the greater of 300 mm or three times the diameter of the inflow pipe.
----
+
* The depth should be the greater of 200 mm or half the inflow pipe diameter.
 +
 
 +
==References==
 +
[[Category:Pretreatment]]

Latest revision as of 20:41, 27 September 2022

This clever design incorporates a level spreading device after a curb cut has narrowed the flow path. This kind of treatment train approach would provide an opportunity to provide pretreatment at the point of concentration. Photo credit: MPCA
Diagram from Wikimedia commons. Credit: U.S. Army Corps of Engineers, Construction Engineering Research Laboratory

Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as vegetated filter strips, bioretention, swales or forested conservation areas[1].

The length of the level spreader should be determined by the design storm inflow rate and type of landscape downstream:

  • 1.4 m of level spreader length per every 0.01 m³/s of inflow when draining to a vegetated filter strip, bioretention, swale or grassed area;
  • 4.3 m of level spreader length per every 0.01 m³/s of inflow when draining to a forested conservation area.
  • The minimum level spreader length is 4 m and the maximum is 40 m.
  • The level spreader lip should be concrete, wood or pre-fabricated metal.
  • The ends of the level spreader section should be tied back into the slope to avoid overflow scouring or erosion around the ends.
  • The width of the level spreader should be the greater of 300 mm or three times the diameter of the inflow pipe.
  • The depth should be the greater of 200 mm or half the inflow pipe diameter.

References[edit]

  1. Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.