Difference between revisions of "Urbanization"

From LID SWM Planning and Design Guide
Jump to navigation Jump to search
 
(18 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
[[File:Natural Ground Cover.png|thumb|500 px|Natural ground cover pre-development conditions]]
 +
[[File:Urban_Hydrology_1.png|thumb|500 px|This image depicts a typical urban hydrologic condition wherein an end-of-pipe control (stormwater management pond) is used to control the peak discharge of urban runoff to a receiving water body.]]
 +
[[File:Urban_Hydrology_3.png|thumb|500 px|Urban hydrology with Low Impact Development]]
 +
{{TOClimit|2}}
 
==Pre-development hydrology==
 
==Pre-development hydrology==
−
[[File:Natural Ground Cover.png|thumb|Natural ground cover pre-development conditions]]
+
In Ontario prior to development, it is typical for rain falling to the surface to be intercepted by the leaves and stems of vegetation, and this is referred to as interception storage. The amount of rain lost to interception storage depends on the kind of vegetation and its growth stage, but abstraction values of 1 – 4 mm are typical <ref>United Nations Food and Agricultural Organization (UNFAO). 1991. A Manual for the Design and Construction of Water Harvesting Schemes for Plant Production. Available at URL: http://www.fao.org/docrep/u3160e/u3160e00.htm#Contents</ref>.  
−
In Ontario prior to development, it is typical for rain falling to the surface to be intercepted by the leaves and stems of vegetation, and this is referred to as interception storage. The amount of rain lost to interception storage depends on the kind of vegetation and its growth stage, but abstraction values of 1 – 4 mm are typical <ref>United Nations Food and Agricultural Organization (UNFAO). 1991. A Manual for the Design and Construction of Water Harvesting Schemes for Plant Production. Available at URL: http://www.fao.org/docrep/u3160e/u3160e00.htm#Contents</ref>. The presence of vegetation also helps to reduce the incidence of soil crusting which can otherwise occur when raindrops impact bare soil surfaces. The root systems of vegetation help to loosen the soil and increase its connected porosity, and this in turn promotes more rapid infiltration. A landscape’s infiltration capacity is also dependent on soil texture; the highest infiltration capacities are typically found in loose, sandy soils, while heavy clay or clay-loam soils usually have smaller [[infiltration]] capacities.
 
  
−
If rain falls at rate which is greater than the underlying soils infiltration rate, it will begin to fill depressions, at which point runoff will begin to be generated. The production of runoff is accelerated as surface slope increases and slope lengths decrease, as both considerations increase surface runoff velocities and decrease the time of concentration <ref>Sharma, K.D. 1986. Runoff behaviour of water harvesting microcatchments. Agricultural Water Management 11 (2): 137-144</ref>.
+
The presence of vegetation also helps to reduce the incidence of soil crusting which can otherwise occur when raindrops impact bare soil surfaces. The root systems of vegetation help to loosen the soil and increase its connected porosity, and this in turn promotes more rapid [[infiltration]]. A landscape’s infiltration capacity is also dependent on soil [[texture]]; the highest infiltration capacities are typically found in loose, sandy soils, while heavy clay or clay-loam soils usually have lower infiltration capacities.
  
−
Under natural conditions, the presence of surface vegetation and leaf litter provides ample opportunity for rainfall to be intercepted, detained and infiltrated – even in area with moderate to steep slopes. Generally speaking, only about 10% of the annual rainfall amount in such areas is lost as surface runoff. The rest of the water supports the growth of vegetation (40%), feeds nearby watercourses (20%) and recharges aquifers (20%).
+
If rain falls at rate which is greater than the underlying soils infiltration rate, it will begin to fill depressions, at which point runoff will begin to be generated. The production of runoff is accelerated as surface [[slope]] increases and slope lengths decrease, as both considerations increase surface runoff velocities and decrease the time of concentration <ref>Sharma, K.D. 1986. Runoff behaviour of water harvesting microcatchments. Agricultural Water Management 11 (2): 137-144</ref>.
 +
Under natural conditions, the presence of surface vegetation and leaf litter provides ample opportunity for rainfall to be intercepted, detained and infiltrated – even in area with moderate to steep slopes.
 +
 
 +
About 10 % of the annual rainfall amount in such areas is lost as surface runoff. The rest of the water supports the growth of vegetation (40 %), feeds nearby watercourses (20 %) and recharges aquifers (20 %).
  
 
==Post-development hydrologic changes==
 
==Post-development hydrologic changes==
 
===Water quantity changes===
 
===Water quantity changes===
−
[[File:Urban_Hydrology_1.png|thumb|This image depicts a typical urban hydrologic condition wherein an end-of-pipe control (stormwater management pond) is used to control the peak discharge of urban runoff to a receiving water body.]]
+
While rainfall intensity, soil and vegetation characteristics, slope length and steepness all play a role in the timing and rate of runoff generation, the creation of impervious surfaces – including rooftops, driveways, roads and parking lots – disrupts rainfall’s ability to penetrate the soil surface and infiltrate.  In heavily urbanized, well-drained areas, the time of concentration is significantly reduced due to the relative smoothness of impervious surfaces, and the dense network of stormwater conveyance infrastructure including gutters, catch basins and sewers.  
−
[[File:Urban_Hydrology_2.png|thumb|The right image depicts a similar upland condition, but without any sort of end-of-pipe stormwater management facility.]]
 
−
While rainfall intensity, soil and vegetation characteristics, slope length and steepness all play a role in the timing and rate of runoff generation, the creation of impervious surfaces – including rooftops, driveways, roads and parking lots – disrupts rainfall’s ability to penetrate the soil surface and infiltrate.  In heavily urbanized, well-drained areas, the time of concentration is significantly reduced due to the relative smoothness of impervious surfaces, and the dense network of stormwater [[conveyance]] infrastructure including gutters, catch basins and subsurface pipes.  
 
  
−
In urban areas which use stormwater ponds to control the peak flow of runoff entering receiving environs the net volume of runoff remains the same, but the rate of release is controlled (left). In older urban areas where stormwater ponds are not commonly in use, the timing and rate of release of stormwater to the receiving environment is uncontrolled, and this is representative of approximately 85% of the pre-existing urban areas throughout Ontario.
+
In urban areas which use stormwater ponds to control the peak flow of runoff entering receiving environs the net volume of runoff remains the same, but the rate of release is controlled. In older urban areas where stormwater ponds are not commonly in use, the timing and rate of release of stormwater to the receiving environment is uncontrolled, and this is representative of approximately 85% of existing urban areas throughout Ontario.  
  
−
The large volumes of stormwater runoff produced under such circumstances overstress conventional stormwater systems leading to flooding, erosion, habitat destruction, degraded water quality, damage to infrastructure systems and post-flooding health-related concerns including mould growth and contaminated water.
+
The large volumes of stormwater runoff produced under such circumstances over stress conventional stormwater systems leading to flooding, erosion, habitat destruction, degraded water quality, damage to infrastructure systems and post-flooding health-related concerns including mould growth and contaminated drinking water supplies.
  
 
===Water quality impacts===
 
===Water quality impacts===
−
The surface runoff generated in urban areas frequently carries with it a cocktail of pollutants. Although it is variable in nature, runoff pollutants are typically derived from a combination of fine sediments from atmospheric deposition, oil, grease and [[heavy metal]]s (including Cd, Cu, Fe, Ni, Pb, Zn, etc.) from vehicular traffic and industrial activities, nutrients derived from lawn fertilizers and pet waste, and – in seasonally cold climates – road salts from [[winter]] maintenance activities <ref>Aryal, R. Vigneswaran, S. Kandasamy, J.; Naidu, R. 2010. Urban Stormwater Quality and Treatment. Korean Journal of Chemical Engineering, 27(5):1343-1359</ref> <ref> Trenouth, W.R. Gharabaghi, B., Perera, N. 2015. Road salt application planning tool for winter de-icing operations. Journal of Hydrology. 524:401-410</ref>. These pollutants accumulate on the road surface during the antecedent dry period between consecutive rainfall events, and are washed off at the onset of rainfall. The majority of particles are washed off with the first flush of stormwater runoff, typically considered to be accounted for with the first 25 mm, or one inch or runoff <ref>Stenstrom, M.K. Kayhanian, M. 2005. First flush phenomenon characterization. Prepared for California Department of Transportation, Division of Environmental Analysis. Available at URL: http://www.dot.ca.gov/hq/env/stormwater/pdf/CTSW-RT-05-073-02-6_First_Flush_Final_9-30-05.pdf</ref>.
+
Surface runoff generated in urban areas frequently carries with it a cocktail of pollutants. Although it is variable in nature, runoff pollutants are typically derived from a combination of fine sediments from atmospheric deposition, oil, grease and [[heavy metals]] (including Cd, Cu, Fe, Ni, Pb, Zn, etc.) from vehicular traffic and industrial activities, nutrients derived from lawn fertilizers and pet waste, and – in seasonally cold climates – road [[salt management|salt]] from winter maintenance activities <ref>Aryal, R. Vigneswaran, S. Kandasamy, J.; Naidu, R. 2010. Urban Stormwater Quality and Treatment. Korean Journal of Chemical Engineering, 27(5):1343-1359</ref> <ref> Trenouth, W.R. Gharabaghi, B., Perera, N. 2015. Road salt application planning tool for winter de-icing operations. Journal of Hydrology. 524:401-410</ref>. These pollutants accumulate on the road surface during the antecedent dry period between consecutive rainfall events, and are washed off at the onset of rainfall. The majority of particles are washed off with the first flush of stormwater runoff, typically considered to be accounted for with the first 25 mm of runoff <ref>Stenstrom, M.K. Kayhanian, M. 2005. First flush phenomenon characterization. Prepared for California Department of Transportation, Division of Environmental Analysis. Available at URL: http://www.dot.ca.gov/hq/env/stormwater/pdf/CTSW-RT-05-073-02-6_First_Flush_Final_9-30-05.pdf</ref>.
−
 
 
−
===Climate-related impacts===
 
−
[[File:Lake_Ontario_2012.png|thumb|Six notable extreme rainfall events have occurred within the past thirteen years in the GTHA, resulting in damages due to flooding. This figure shows a notable extreme rainfall “near-miss” event, labelled “Lake Ontario 2012”.]]
 
−
[[File:Radar_tracking_August_2012.png|thumb|Radar tracking of the August 10, 2012 extreme rainfall event. The Lake Ontario nearshore experienced sustained intensities approaching 200 mm/hr, while the southern portion of Peel Region had no measurable precipitation. (Source: Risk Sciences International)]]
 
−
[[File:Lake_Ontario_Drought_2007.png|thumb|Drought conditions at Island Lake in the summer of 2007]]
 
−
Since 1995, Ontario has had a weather-related state of emergency almost every single year <ref>Swiss Re (in collaboration with Institute for Catastrophic Loss Reduction) (2010). Making Flood Insurable for Canadian Homeowners. Available at URL: http://www.iclr.org/images/Making_Flood_Insurable_for_Canada.pdf</ref>. The City of Windsor saw extreme events that caused severe flooding in 2007, 2010, 2016 and 2017 <ref>City of Windsor. 2012. Climate Change Adaptation Plan. Available at URL: http://www.citywindsor.ca/residents/environment/environmental-master-plan/documents/windsor%20climate%20change%20adaptation%20plan.pdf</ref>. The Ottawa region experienced one extreme event every year for five years, and in the Greater Toronto Area (GTA), there have been four extreme rainfall events in the past ten years <ref>Environment Canada. 2014. Climate. Available at URL: http://climate.weather.gc.ca/</ref>. Such high intensity events produce heavy rainfall in relatively short periods of time. While it is reasonable to expect runoff to be produced under such conditions – particularly when rain falls which exceeds a soil’s hydraulic conductivity - the production of stormwater is exacerbated in urban areas where the overwhelming majority of surfaces are impervious. The problems associated with managing stormwater volumes are exacerbated when dense stormsewer networks efficiently convey stormwater runoff volumes from a large contributing upland area to a single outlet location, such as a stormsewer outfall in a river or stream.
 
−
 
 
−
In July 2013, the GTA experienced its most severe storm event in 60 years. Nearly five inches (126 mm) of rain fell in a two-hour period. In comparison, during Hurricane Hazel (a devastating event in 1954 where 81 lives were lost), the two-hour maximum precipitation was 91 mm and the total amount of rainfall was 285 mm over nearly two days <ref>Toronto Star. 2013. Monday’s storm vs. Hurricane Hazel. Available at URL: http://www.thestar.com/opinion/letters_ to_the_editors/2013/07/14/mondays_storm_vs_hurricane_hazel.html</ref>. Conventional municipal drainage systems could not carry stormwater away fast enough. Roads and highways were overcome with floodwater closing major transportation corridors including Highway 427. GO Train passengers were stranded, and power outages and basement flooding were widespread with property damage of more than $1 billion <ref>Insurance Bureau of Canada (IBC). 2016. Facts of the property & casualty insurance industry in Canada. 36th edition, ISSN 1197 3404. Available at URL: http://assets.ibc.ca/Documents/Facts%20Book/Facts_Book/2016/Facts-Book-2016.pdf</ref>.
 
−
 
 
−
While it is nearly impossible to ascribe the cause of a single event to the broader issue of climate change, the trend is clear: an increasing number of high-intensity, short-duration (HISD) events are impacting our urban areas, exacerbating the stresses on overtaxed stormwater infrastructure. The figure highlights a series of seven recent extreme rainfall events which have struck the Greater Toronto and Hamilton Area (GTHA).
 
−
 
 
−
On August 10, 2012, a large storm tracked across Lake Ontario parallel to the Canadian shoreline. Situated only 15 km southeast of Mississauga, this event lasted 6.5 hours and had estimated sustained intensities of 150-200 mm/h (see Figure). While the impacts of extreme rainfall events on urban areas cannot be ignored, the increasingly prolonged, dry inter-event periods necessitate that stormwater infiltration and percolation be maximized in order sustain base flows in support of aquatic ecosystems.
 
−
 
−
While urban flooding and extreme rainfall garner the most attention in discussions pertaining to stormwater management, it is crucial that consideration also be given to the management of our water cycle during dry periods as well. Collectively, we need to be able to manage extreme rainfall events such as the July 8, 2013 storm, combined rain and snow events such as that which caused the Bow River flood in Calgary in 2013, and extended periods of drought as occurred in southern Ontario in 2007. Drought preparedness is required if we are to sustain riverine baseflows, ensure the security of drinking water resources and optimize both water and waste water infrastructure.
 
−
 
 
−
As municipalities grapple with these new climate realities and their associated costs, they are rethinking how to manage stormwater using a variety of innovative solutions. The figure illustrates what has already happened in Ontario under conditions of prolonged drought. The Island Lake Reservoir, located near the Town of Orangeville, saw significant drawdown during the summer of 2007 after a period of prolonged drought.
 
−
 
 
−
Reliant on groundwater for its municipal supply, continued pumping by the Town led to a significant drawdown within the reservoir. This was problematic not just for the ecosystem of the Lake, but for the downstream wastewater treatment plan as well, which relies on discharges from the reservoir in order to ensure that treated effluent can safely be assimilated by the receiving watercourse.
 
  
 
==Alleviating pressures using LID==
 
==Alleviating pressures using LID==
−
[[File:Urban_Hydrology_3.png|thumb|Urban hydrology with Low Impact Development]]
 
−
[[File:Pearson_Graph.png|thumb|Typically designed to handle the smaller, most frequent storm events, LID practices in Southern Ontario are usually sized according to the 90th percentile event]]
 
 
There are many reasons that make LID the smart choice when it comes to stormwater management. The creation of well-designed permeable landscapes provides an opportunity to capture, retain and infiltrate stormwater runoff close to its source.  Rather than treat stormwater as a waste product to be discarded, LID recognizes stormwater for what it is – a resource to be safeguarded and harnessed for the benefit of both the built and natural environment.
 
There are many reasons that make LID the smart choice when it comes to stormwater management. The creation of well-designed permeable landscapes provides an opportunity to capture, retain and infiltrate stormwater runoff close to its source.  Rather than treat stormwater as a waste product to be discarded, LID recognizes stormwater for what it is – a resource to be safeguarded and harnessed for the benefit of both the built and natural environment.
 +
A central tenet underpinning low impact development approaches to stormwater management is the treatment train approach, which describes a hierarchical suite of practices which manage rainfall where it falls, followed by the attenuation, filtration and infiltration of stormwater along its path of travel and – eventually – using an end-of-pipe detention and polishing process. While many LID practices – including [[bioretention]], soakaway pits and others – are not necessarily intended to remedy issues related to urban flooding per se, they are effective at easing the pressure on aging, overburdened stormwater infrastructure. That being said, there are new options in the LID toolkit which have the capacity to provide both peak flow and large event runoff volume control.
  
−
A central tenet underpinning low impact development approaches to stormwater management is the [[treatment train]] approach, which describes a hierarchical suite of practices which manage rainfall where it falls, followed by the attenuation, filtration and infiltration of stormwater along its path of travel and – eventually – using an end-of-pipe detention and polishing process. While many LID practices – including [[bioretention]], soakaway pits and others – are not necessarily intended to remedy issues related to urban flooding per se, they are effective at easing the pressure on aging, overburdened stormwater infrastructure. That being said, there are new options in the LID toolkit which have the capacity to provide both peak flow and large event runoff volume control.
+
==References==
−
 
+
[[category: Background]]
−
Typically designed to handle the smaller, most frequent storm events, LID practices in Southern Ontario are usually sized according to the [[Runoff_volume_control_target| 90th percentile event]]. In many areas this translates into events that are <30 mm in size. Note that 25 mm is considered to be a suitable representation of the ‘first flush’ volume, and that controlling this amount of runoff provides stormwater engineers with control over 90% of the mean annual pollutant load <ref>Pitt, R. 1999.  Small Storm Hydrology and Why it is Important for the Design of Stormwater Control Practices. In: Advances in Modeling the Management of Stormwater Impacts, Volume 7. Computational Hydraulics International, Guelph, Ontario and Lewis Publishers/CRC Press. 1999</ref>.
 
−
 
 
−
----
 
−
 
 
 
[[category:Planning]]
 
[[category:Planning]]

Latest revision as of 18:06, 6 October 2022

Natural ground cover pre-development conditions
This image depicts a typical urban hydrologic condition wherein an end-of-pipe control (stormwater management pond) is used to control the peak discharge of urban runoff to a receiving water body.
Urban hydrology with Low Impact Development

Pre-development hydrology[edit]

In Ontario prior to development, it is typical for rain falling to the surface to be intercepted by the leaves and stems of vegetation, and this is referred to as interception storage. The amount of rain lost to interception storage depends on the kind of vegetation and its growth stage, but abstraction values of 1 – 4 mm are typical [1].

The presence of vegetation also helps to reduce the incidence of soil crusting which can otherwise occur when raindrops impact bare soil surfaces. The root systems of vegetation help to loosen the soil and increase its connected porosity, and this in turn promotes more rapid infiltration. A landscape’s infiltration capacity is also dependent on soil texture; the highest infiltration capacities are typically found in loose, sandy soils, while heavy clay or clay-loam soils usually have lower infiltration capacities.

If rain falls at rate which is greater than the underlying soils infiltration rate, it will begin to fill depressions, at which point runoff will begin to be generated. The production of runoff is accelerated as surface slope increases and slope lengths decrease, as both considerations increase surface runoff velocities and decrease the time of concentration [2]. Under natural conditions, the presence of surface vegetation and leaf litter provides ample opportunity for rainfall to be intercepted, detained and infiltrated – even in area with moderate to steep slopes.

About 10 % of the annual rainfall amount in such areas is lost as surface runoff. The rest of the water supports the growth of vegetation (40 %), feeds nearby watercourses (20 %) and recharges aquifers (20 %).

Post-development hydrologic changes[edit]

Water quantity changes[edit]

While rainfall intensity, soil and vegetation characteristics, slope length and steepness all play a role in the timing and rate of runoff generation, the creation of impervious surfaces – including rooftops, driveways, roads and parking lots – disrupts rainfall’s ability to penetrate the soil surface and infiltrate. In heavily urbanized, well-drained areas, the time of concentration is significantly reduced due to the relative smoothness of impervious surfaces, and the dense network of stormwater conveyance infrastructure including gutters, catch basins and sewers.

In urban areas which use stormwater ponds to control the peak flow of runoff entering receiving environs the net volume of runoff remains the same, but the rate of release is controlled. In older urban areas where stormwater ponds are not commonly in use, the timing and rate of release of stormwater to the receiving environment is uncontrolled, and this is representative of approximately 85% of existing urban areas throughout Ontario.

The large volumes of stormwater runoff produced under such circumstances over stress conventional stormwater systems leading to flooding, erosion, habitat destruction, degraded water quality, damage to infrastructure systems and post-flooding health-related concerns including mould growth and contaminated drinking water supplies.

Water quality impacts[edit]

Surface runoff generated in urban areas frequently carries with it a cocktail of pollutants. Although it is variable in nature, runoff pollutants are typically derived from a combination of fine sediments from atmospheric deposition, oil, grease and heavy metals (including Cd, Cu, Fe, Ni, Pb, Zn, etc.) from vehicular traffic and industrial activities, nutrients derived from lawn fertilizers and pet waste, and – in seasonally cold climates – road salt from winter maintenance activities [3] [4]. These pollutants accumulate on the road surface during the antecedent dry period between consecutive rainfall events, and are washed off at the onset of rainfall. The majority of particles are washed off with the first flush of stormwater runoff, typically considered to be accounted for with the first 25 mm of runoff [5].

Alleviating pressures using LID[edit]

There are many reasons that make LID the smart choice when it comes to stormwater management. The creation of well-designed permeable landscapes provides an opportunity to capture, retain and infiltrate stormwater runoff close to its source. Rather than treat stormwater as a waste product to be discarded, LID recognizes stormwater for what it is – a resource to be safeguarded and harnessed for the benefit of both the built and natural environment. A central tenet underpinning low impact development approaches to stormwater management is the treatment train approach, which describes a hierarchical suite of practices which manage rainfall where it falls, followed by the attenuation, filtration and infiltration of stormwater along its path of travel and – eventually – using an end-of-pipe detention and polishing process. While many LID practices – including bioretention, soakaway pits and others – are not necessarily intended to remedy issues related to urban flooding per se, they are effective at easing the pressure on aging, overburdened stormwater infrastructure. That being said, there are new options in the LID toolkit which have the capacity to provide both peak flow and large event runoff volume control.

References[edit]

  1. ↑ United Nations Food and Agricultural Organization (UNFAO). 1991. A Manual for the Design and Construction of Water Harvesting Schemes for Plant Production. Available at URL: http://www.fao.org/docrep/u3160e/u3160e00.htm#Contents
  2. ↑ Sharma, K.D. 1986. Runoff behaviour of water harvesting microcatchments. Agricultural Water Management 11 (2): 137-144
  3. ↑ Aryal, R. Vigneswaran, S. Kandasamy, J.; Naidu, R. 2010. Urban Stormwater Quality and Treatment. Korean Journal of Chemical Engineering, 27(5):1343-1359
  4. ↑ Trenouth, W.R. Gharabaghi, B., Perera, N. 2015. Road salt application planning tool for winter de-icing operations. Journal of Hydrology. 524:401-410
  5. ↑ Stenstrom, M.K. Kayhanian, M. 2005. First flush phenomenon characterization. Prepared for California Department of Transportation, Division of Environmental Analysis. Available at URL: http://www.dot.ca.gov/hq/env/stormwater/pdf/CTSW-RT-05-073-02-6_First_Flush_Final_9-30-05.pdf

refers to the characteristics and functions of a system prior to urban development.

A structural best management practice that is located at the end of a flow conveyance route. End-of-Pipe Controls on surface and below ground but are not limited to wet ponds, constructed wetlands and other similar systems.

A body of water smaller than a lake, often artificially formed.

The greatest volume of stream flow occurring during a storm event.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

Low impact development is a stormwater management and land development strategy applied at the parcel and subdivision scale that emphasizes conservation and use of on-site natural features integrated with engineered, small scale hydrologic controls to more closely mimic pre-development hydrologic functions.

A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

refers to the characteristics and functions of a system prior to urban development.

The interception, storage and eventual evaporation of rainfall from vegetation canopies.

The porosity (n) of a mixture is the ratio of the volume of void-space to the total or bulk volume of the mixture. It is closely related to the concept of void ratio (e) where void ratio is the ratio of the volume of void-space to the volume of solids. n = Volume of voids/Total volume of mixture = e/(1+e)

1. A mineral soil separate consisting of particles less than 0.002 millimeter in equivalent diameter. 2. A soil texture class. 3. (Engineering) A fine-grained soil (more than 50 percent passing the No. 200 Sieve) that has a high plasticity index in relation to the liquid limit. (Unified Soil Classification System).

The rate at which stormwater percolates into the subsoil measured in inches per hour.

The time needed for a drop of water to reach the outlet of a catchment from the most remote location within the catchment.

Layer of rock or soil that holds or transmits water.

The rate of rainfall in millimeters per hour.

A hard surface area (e.g., road, parking area or rooftop) that prevents or retards the infiltration of water into the soil.

Ground depression acting as a flow control and water treatment structure, that is normally dry.

Refers to the conditions in which an organism lives and survives or the conditions in which an organism resides. These conditions can be described as aspects of a “physical”, “social” or an “economic” environment, depending on the perspective perceived by the observer.

(1) The wearing away of the land surface by moving water, wind, ice or other geological agents, including such processes as gravitation creep; (2) Detachment and movement of soil or rock fragments by water, wind, ice or gravity (i.e. Accelerated, geological, gully, natural, rill, sheet, splash, or impact, etc).

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

The period of time between consecutive storms or rainfall events.

The delivery of a disproportionately large load of pollutants during the early part of storms due to the rapid runoff of accumulated pollutants. The first flush of runoff has been defined several ways (e.g., 10 mm per impervious area).

Initial pulse of stormwater runoff which picks up the pollutants that have settled on surfaces during the dry period. The first flush contains the highest pollutant concentrations.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

Stormwater management following the hierarchical approach: Source Control measures, Conveyance Control measure and End of Pipe treatment to achieve the water quality and water balance target for lot level development of the preferred strategy.

A combination of lot level, conveyance, and end-of-pipe stormwater management practices.

Reduction of peak flow and increase of the duration of the flow event.

The technique of removing pollutants from runoff as it infiltrates through the soil.

The temporary storage of stormwater to control discharge rates, and allow for sedimentation.

An underground water storage reservoir into which stormwater is directed and allowed to percolate into the underlying native subsoil.

An excavated area lined with geotextile filter cloth and filled with clean granular stone or other void forming material, that receives runoff and allow it to infiltrate into the native soil; can also be referred to as infiltration galleries, French drains, dry wells or soakaway pits.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

The delivery of a disproportionately large load of pollutants during the early part of storms due to the rapid runoff of accumulated pollutants. The first flush of runoff has been defined several ways (e.g., 10 mm per impervious area).

Initial pulse of stormwater runoff which picks up the pollutants that have settled on surfaces during the dry period. The first flush contains the highest pollutant concentrations.

Retrieved from "https://wiki.sustainabletechnologies.ca/index.php?title=Urbanization&oldid=14408"