Permeable paving

Overview

Permeable paving is ideal for:

• Projects which accommodate light vehicular traffic or pedestrian traffic,
• Sites which cannot accommodate additional surface area for bioretention

The fundamental components of a permeable paving system are:

• interlocking blocks with infiltration spaces between, or
• a poured in place surface without fines, so that the finish is pervious to water
• a bedding course to stabilize the surface
• underground storage layer of aggregate.

Additional components may include:

• an underdrain system

Planning considerations

Landscaping

Landscaped areas must drain away from permeable pavement to prevent sediments from running onto the surface. Urban trees will benefit from being surrounded by permeable pavement rather than impervious cover, because their roots receive more air and water. Interlocking pavers used around the base of a tree may be removed as the tree grows.

Design

Sizing in TTT

Permeable pavements is found within the LID toolbox

Surface
Berm height (mm)	This is the height of the curb which constrains the overland sheet flow of water. Where curb cuts or other outlet exists at the lowest point of the pavement, the suggested value is 0.
Surface roughness (Manning’s n)	Lower numbers indicate less surface obstruction and result in faster flow. Suggested range for pavement 0.01 – 0.02
Surface slope (%)	Typically between 1 – 4% (>2% recommended Effective grading)
Pavement
Thickness (mm)	This is the thickness of just the pre-cast blocks (or depth of asphalt/concrete poured in place).
Void ratio	This most commonly refers to the jointing material used between precast blocks. Suggest 0.4 unless otherwise tested. Where a pervious product is poured in place, an appropriate figure should be obtained from the manufacturer.
Impervious surface fraction	This is the proportion of the total pavement taken up with the pre-cast blocks and will vary between products; an example value may be 0.85. Where a pervious product is poured in place, this value will be 0.
Permeability (mm/hr)	This is the permeability of the joint material in block systems. Where the permeability of the bulk surface is measured and known instead, the impervious fraction can be adjusted to model a block surface as continuously permeable instead.
Clogging factor	0.5 to model a matured system?
Soil (Bedding layer?)
Thickness (mm)	Depth of bedding layer
Porosity (fraction)	Suggested value 0.4 unless otherwise tested (see OPSS aggregates)
Field capacity (fraction)	Suggested range 0.10 - 0.12 for sand
Wilting point (fraction)	Suggested value 0.03 for sand
Conductivity (mm/hr)	Suggested range 100 – 250 mm/hr for sand
Conductivity slope	Suggested value 45 for sand
Suction head (mm)	Suggested value 50 for sand
Storage
Thickness (mm)	Depth of all aggregate bases
Void ratio	Suggested value 0.4 unless otherwise tested
Seepage rate (mm/hr)	Infiltration rate of native soil
Clogging factor	0.5 to model a matured system?
Design drawdown time (hrs)	Maybe 72 or 96 hours? See Drainage time
Drain (underdrain)
Flow coefficient	Suggested value 1
Flow exponent	Suggested value 1
Offset height	This is the height from the base of the cell to the height at which the drain discharges. In some designs this may be the height of the perforated pipe within the storage layer. In other designs this height is adjusted by creating an upturn in the discharge pipe. Permeable pavements

Geotextile

The properties of geotextiles vary widely.

See Clogging for notes on their application in LID structures.

Geotextiles can be used to prevent downward migration of smaller particles in to larger aggregates, and slump of heavier particles into finer underlying courses. Geotextiles are commonly used on low strength soils (CBR<4). The formation of biofilm on geotextiles has also been shown to improve water quality:

• By degrading petroleum hydrocarbons
• By reducing organic pollutant and nutrient concentrations
• When installing geotextiles an overlap of 150 - 300 mm should be used.

Material specifications should conform to OPSS 1860 for Class II geotextile fabrics . Note when expansive clays are present, a non-infiltrating design may be necessary. If used, geotextile socks around perforated pipes should conform to ASTM D6707 with minimum water flow rate conforming to ASTM D4491 (12,263 L/min/m² at 5 cm head).

• Fabrics should be woven monofilament or non-woven needle punched.
• Woven slit film and non-woven heat bonded fabrics should not be used, as they are prone to clogging.

In choosing a product, consider:

1. The maximum forces that will be exerted on the fabric (i.e., what tensile, tear and puncture strength ratings are required?),
2. The load bearing ratio of the underlying native soil (i.e. is the geotextile needed to prevent downward migration of aggregate into the native soil?),
3. The texture (i.e., grain size distribution) of the overlying and underlying materials, and
4. The suitable apparent opening size (AOS) for non-woven fabrics, or percent open area (POA) for woven fabrics, to maintain water flow even with sediment and microbial film build-up.

Recommended criteria for selection of geotextile fabric

Percent soil/filter media passing 0.075 mm (#200 sieve)	Non-woven fabric apparent opening size (AOS, mm)	Woven fabric percent open area (POA, %)	Permittivity (sec-1)
>85	≤ 0.3	-	0.1
50 - 85	≤ 0.3	≥ 4	0.1
15 - 50	≤ 0.6	≥ 4	0.2
5 - 15	≤ 0.6	≥ 4	0.5
≤ 5	≤ 0.6	≥ 10	0.5

Performance research

http://www.mdpi.com/2073-4441/7/4/1595/htm

---

Proprietary Links

In our effort to make this guide as functional as possible, we have decided to include proprietary systems and links to manufacturers websites.
Inclusion of such links does not constitute endorsement by the Sustainable Technologies Evaluation Program.
Lists are ordered alphabetically; link updates are welcomed using the form below.

Pre-cast

• Eco-Optioc, Unilock
• Enviro Pavers, Oaks
• Pavedrain, distributed by Nilex
• Terra flo, Santerra
• Stormcrete

An alternative practice to traditional impervious pavement, prevents the generation of runoff by allowing precipitation falling on the surface to infiltrate through the surface course into an underlying stone reservoir and, where suitable conditions exist, into the native soil.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

An alternative practice to traditional impervious pavement, prevents the generation of runoff by allowing precipitation falling on the surface to infiltrate through the surface course into an underlying stone reservoir and, where suitable conditions exist, into the native soil.

Soil particles with a diameter less than 0.050 mm.

A broad category of particulate material used in construction, including sand, gravel, crushed stone, slag, recycled concrete and geosynthetic aggregates, and available in various particulate size gradations.

A perforated pipe used to assist the draining of soils.

An alternative practice to traditional impervious pavement, prevents the generation of runoff by allowing precipitation falling on the surface to infiltrate through the surface course into an underlying stone reservoir and, where suitable conditions exist, into the native soil.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

A hard surface area (e.g., road, parking area or rooftop) that prevents or retards the infiltration of water into the soil.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

A mixture of mineral aggregates bound with bituminous materials, used in the construction and maintenance of paved surfaces.

The void ratio (e) of a mixture is the ratio of the volume of void-space to the volume of solids. It is closely related to the concept of porosity (n) where porosity is the ratio of the volume of void-space to the total or bulk volume of the mixture. e = Volume of voids/Volume of solids = n/(1-n)

A hard surface area (e.g., road, parking area or rooftop) that prevents or retards the infiltration of water into the soil.

The porosity (n) of a mixture is the ratio of the volume of void-space to the total or bulk volume of the mixture. It is closely related to the concept of void ratio (e) where void ratio is the ratio of the volume of void-space to the volume of solids. n = Volume of voids/Total volume of mixture = e/(1+e)

Mineral particles which are smaller than 2 mm, and which are free of appreciable quantities of clay and silt. Coarse sand usually designates sand grains with particle size between 0.2 and 0.02 mm.

The rate at which stormwater percolates into the subsoil measured in inches per hour.

The natural ground material characteristic of or existing by virtue of geographic origin.

The period between the maximum water level and the minimum level (dry weather or antecedent level).

Filter fabric that is installed to separate dissimilar soils and provide runoff filtration and contaminant removal benefits while maintaining a suitable rate of flow; may be used to prevent fine-textured soil from entering a coarse granular bed, or to prevent coarse granular from being compressed into underlying finer-textured soils.

A broad category of particulate material used in construction, including sand, gravel, crushed stone, slag, recycled concrete and geosynthetic aggregates, and available in various particulate size gradations.

Filter fabric that is installed to separate dissimilar soils and provide runoff filtration and contaminant removal benefits while maintaining a suitable rate of flow; may be used to prevent fine-textured soil from entering a coarse granular bed, or to prevent coarse granular from being compressed into underlying finer-textured soils.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

The engineered soil component of bioretention cell or dry swale designs, typically with a high rate of infiltration and designed to retain contaminants through filtration and adsorption to particles.

Gravel, or crushed stone of various size gradations (i.e., diameter), used in construction; void forming material used as bedding and runoff storage reservoirs and underdrains in stormwater infiltration practices.