Bioretention: Filter media

Sandy filter media mix.

It is recommended that the mixture comprises:

One of these two blend options

	Blend A: Drainage priority	Blend B: Water quality priority
Application	Higher I/P ratio	More diverse planting, Improved metals and phosphorus retention.
Proportions	70 - 80 % coarse sand 20 - 30 % organic soil components and additives	70 - 80 % coarse sand 10 - 15 % topsoil 10 - 15 % organic soil components and additives

Filter media should be obtained premixed from a vendor and meet all municipal, provincial and federal environmental standards.
Mixing of sand, topsoil and compost should be done in a manner that preserves topsoil peds.
The mixture should be free of stones, stumps, roots, or other debris larger than 50 mm diameter.
Samples of the filter media should be dried, ground and tested to ensure they meet the following specifications:

Bioretention filter media

Characteristic	Criterion	Recommended method
Texture	<20 % fines	Hygrometer
Organic matter (OM)	5 - 10 %	ASTM D2974-14, Standard test methods for moisture, ash and organic matter of peat and other organic soils.
Phosphorus	12 - 40 ppm	'Bray' is most common in Ontario. Alternatives include 'Mehlich I or III', or 'Olsen'.
Cationic exchange capacity(CEC)	10 meq/100 g	ASTM D7503-10, Standard test method for measuring the exchange complex and cation exchange capacity of inorganic fine grained soils.
Hydraulic conductivity	> 25 mm/hr < 250 mm/hr	Falling head or constant head KSAT

Note that grain size distribution does not form part of the recommended acceptance criteria. Whilst this information may be useful in designing blends, the disconnect between hydraulic conductivity and the uniformity of gradation makes it far less important then measuring the hydraulic conductivity directly

Sand

Particle size distribution graph for ASTM C33 sand, as described in table

• Coarse sand for LID construction shall be washed clean and free of toxic materials.
• The pH of the sand shall be ≤ 7.0.
• The coarse sand shall have a fineness modulus index between 2.8 and 3.1 according to ASTM C33/C33M, or otherwise meet the gradation below.

Particle size distribution

Sieve	Percent passing
9.5 mm	100
4.75 mm (No.4)	95 - 100
2.36 mm (No.8)	80 - 100
1.18 mm (No.16)	50 - 85
0.60 mm (No.30)	25 - 50
0.30 mm (No.50)	5 - 30
0.15 mm (No.100)	0 - 10
0.075 mm (No.200)	≤ 3

Topsoil

• Topsoil may be material that was stripped from the project site and stored in stockpiles for re-use, or material imported to the site from a supplier provided the physical and chemical characteristics are within acceptable ranges.
• Topsoil shall be in compliance with Ontario Regulation 153/04 Record of Site Condition standards for soil quality or as amended through Ontario Management of Excess Soil - A Guide for Best Management Practices.
• Soil laboratory reports shall certify the material to be suitable for re-use on residential, parkland, institutional, industrial, commercial, or community landscapes for the germination of seeds and the support of vegetative growth.

The factors to consider in determining if a topsoil is suitable for use as planting soil for a vegetated stormwater practice, or use in producing a bioretention filter media mixture include the following:

• Must be friable and capable of sustaining vigorous plant growth;
• Must be free from toxic material and roots, stones or debris over 50 mm (2") in diameter;
• Should not have been passed through sieves or screens smaller than 50 mm (2”) to avoid eliminating peds;
• Should have a Loamy Sand, Sandy Loam, Sandy Clay Loam, Loam or Silty Loam soil texture;
• For use as planting soil for a vegetated stormwater practice , the topsoil must contain a minimum of 5% organic matter by dry weight or be amended so, through addition of an organic soil conditioner;
• For use in producing bioretention filter media Blend B (water quality treatment priority), the topsoil must contain at least 9%, and not greater than 36% clay-sized particles and at least 2% organic matter by dry weight.
• Must have a pH of between 6.0 and 8.0;
• Must have a sodium absorption ratio less than 15;
• Must have a cationic exchange capacity greater than 10 milliequivalents per 100 grams (meq/100 g).

Specify that 4 litre samples of topsoil, from each source to be drawn upon, be provided to the consultant for visual inspection, along with topsoil quality test results from an accredited soil testing laboratory, or a quality assurance certificate from the supplier.

We recommend a planting soil or filter media depth of 300 mm to support grasses, 600 mm for shrubs and perennials, and 1000 mm for trees.

Organic components

Compost

Compost is the most widely used organic component. It's use in bioretention facilities is well established and documented. Low-phosphorus composts should always be sought for use in low impact development facilities, including bioretention. These are typically created from feedstocks including yard, leaf, and wood waste, and must exclude manures, biosolids, and food scraps.
Compost Specifications

Even low-phosphorus composts are known to export phosphorus over many years. The use of compost is not recommended in watersheds for which phosphorus pollution is a concern. There are alternatives which have undergone field study, each of which has a number of benefits and potential concerns:

Organic soil components

Material	Benefits	Concerns
Coconut coir	Doesn't leach phosphorus	Requires importation
Wood chip	Doesn't leach phosphorus Promotes nitrogen removal from water	-
Peat Moss	Doesn't leach phosphorus	Sustainability controversial
Shredded newspaper (see: Pittmoss)

Coconut coir

http://www.modularwetlands.com/new/wp-content/uploads/2015/11/2-Bioretention-Synthesis-2015-DAhearn.pdf

Wood derivatives

https://www.unh.edu/unhsc/sites/default/files/media/unhsc_bsm_spec_2-28-17_0.pdf https://www.unh.edu/unhsc/sites/unh.edu.unhsc/files/STONE%20THESIS%20FINAL.pdf https://jbioleng.biomedcentral.com/articles/10.1186/s13036-017-0057-4 (focus on denitrification)

Additives

Typically these components would comprise 5- 10 % by volume of the filter media mixture. It is recommended that this fraction be taken from the topsoil or the organic portion otherwise; keeping the sand as minimum 65 % by volume. Design innovations to improve water quality treatment performance of filter media mixtures involve the incorporation of additives to enhance retention of reactive or dissolved pollutants. A number of granular amendments have been demonstrated to improve nutrient removal from discharge water in BMPs such as bioretention systems, stormwater planters, absorbent landscapes, sand filters or green roofs.

There are two primary processes involved, chemical precipitation and adsorption. Both mechanisms are ultimately finite, but have been shown in some cases to make significant improvements on the discharged water quality over several years. For instance, a two year STEP research study that compared standard bioretention media, to the same media amended with Sorbtive™ in one plot and iron enriched sand (aka red sand) in another showed statistically significant improvements in effluent phosphorus concentrations from the two media amended plots (STEP, 2019).

Determining when additive enhanced filter media needs replacing or maintenance represents a new challenge for stormwater asset managers, as there are no suitable visual indicators. Erickson et al. (2018) suggest effluent sampling and laboratory testing to identify when enhanced filter media pollutant retention is waning, or periodic sampling and batch (laboratory) testing of filter media to directly measure its capacity to retain the targeted pollutants. Periodic replacement of filter media at inlet locations should be considered as an operation and maintenance best practice to maintain treatment performance.

In our effort to make this guide as functional as possible, we have decided to include proprietary systems and links to manufacturers websites.
Inclusion of such links does not constitute endorsement by the Sustainable Technologies Evaluation Program.
Lists are ordered alphabetically; link updates are welcomed using the form below.

Filter Media Additives

Material	Benefits	Potential concerns
Biochar	Renewable Enhances soil aggregation, water holding capacity and organic carbon content	Currently expensive Energy intensive to produce Some sources say ineffective for phosphorus removal
Bold & GoldTM	Documented total phosphorus removal of up to 71%	Proprietary
Iron filings or Zero valent iron (ZVI)	Proven phosphorus retention Retained phosphorus is stable	May harm plants Removal efficiency declines with increased concentration of incoming phosphorus
Red sand or Iron-enriched sand	Proven phosphorus removal Also removes TSS	Poor orthophosphate removal in hypoxic or anoxic conditions
Smart SpongeTM	Removes phosphorus, as well as TSS, fecal coliform bacteria and heavy metals Non-leaching	1-3 year lifespan, after which the product is removed as solid waste Proprietary
Sorbtive MediaTM	High phosphorus removal efficiency	Proprietary
Water treatment residuals	Waste product reuse	Quality control (capabilities depend on source, treatment methods, storage time)

---

---

The engineered soil component of bioretention cell or dry swale designs, typically with a high rate of infiltration and designed to retain contaminants through filtration and adsorption to particles.

The ratio of the impervious catchment (drainage) area to the pervious (footprint) area of the receiving BMP.

The engineered soil component of bioretention cell or dry swale designs, typically with a high rate of infiltration and designed to retain contaminants through filtration and adsorption to particles.

Mineral particles which are smaller than 2 mm, and which are free of appreciable quantities of clay and silt. Coarse sand usually designates sand grains with particle size between 0.2 and 0.02 mm.

Decayed organic material used as a plant fertilizer. Compost helps to support healthy plant growth through the slow release of nutrients and the retention of moisture in the soil.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

Soil particles with a diameter less than 0.050 mm.

A parameter that describes the capability of a medium to transmit water.

Mineral particles which are smaller than 2 mm, and which are free of appreciable quantities of clay and silt. Coarse sand usually designates sand grains with particle size between 0.2 and 0.02 mm.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

1. A mineral soil separate consisting of particles less than 0.002 millimeter in equivalent diameter. 2. A soil texture class. 3. (Engineering) A fine-grained soil (more than 50 percent passing the No. 200 Sieve) that has a high plasticity index in relation to the liquid limit. (Unified Soil Classification System).

1. A mineral soil separate consisting of particles less than 0.002 millimeter in equivalent diameter. 2. A soil texture class. 3. (Engineering) A fine-grained soil (more than 50 percent passing the No. 200 Sieve) that has a high plasticity index in relation to the liquid limit. (Unified Soil Classification System).

Decayed organic material used as a plant fertilizer. Compost helps to support healthy plant growth through the slow release of nutrients and the retention of moisture in the soil.

A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

Gravel, or crushed stone of various size gradations (i.e., diameter), used in construction; void forming material used as bedding and runoff storage reservoirs and underdrains in stormwater infiltration practices.

Any form of rain or snow.

The attachment of gas, vapour or dissolved matter onto the surface of solid materials.

Sustainable Technologies Evaluation Program

Total suspended solids

A shallow constructed channel, often grass-lined, which is used as an alternative to curb and channel, or as a pretreatment to other measures. Swales are generally characterized by a broad top width to depth ratio and gentle grades.

Surface runoff from at-grade surfaces, resulting from rain or snowmelt events.