Difference between revisions of "Level spreaders"

From LID SWM Planning and Design Guide
Jump to navigation Jump to search
(Created page with "Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as vegetated filter strips or swales...")
 
 
(14 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as [[vegetated filter strips]] or  [[swales]]. <ref>Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.</ref>.
+
[[File:Levelspread.jpg|thumb|This clever design incorporates a level spreading device after a [[curb cut]] has narrowed the flow path. This kind of treatment train approach would provide an opportunity to provide [[pretreatment]] at the point of concentration. Photo credit: [https://www.pca.state.mn.us/featured/when-it-rains-it-flows MPCA] ]] 
 +
[[File:Level spreader diagram.jpg|thumb|Diagram from Wikimedia commons. Credit: U.S. Army Corps of Engineers, Construction Engineering Research Laboratory]]
  
The length of the level spreader should be determined by the type of filter area and the design flow:
+
Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as [[vegetated filter strips]], [[Bioretention|bioretention]], [[swales]] or forested conservation areas<ref>Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.</ref>.
* 1.4 m of level spreader length per every 0.01 cubic meter per second (cms) of inflow for discharges to a filter strip or turf conservation area;
+
 
* 4.3 m of level spreader length per every 0.01 cms of inflow when the spreader discharges to a forested conservation area.
+
The length of the level spreader should be determined by the design storm inflow rate and type of landscape downstream:
 +
* 1.4 m of level spreader length per every 0.01 m³/s of inflow when draining to a [[vegetated filter strips|vegetated filter strip]], [[Bioretention| bioretention]], [[Swale| swale]] or grassed area;
 +
* 4.3 m of level spreader length per every 0.01 m³/s of inflow when draining to a forested conservation area.
 
* The minimum level spreader length is 4 m and the maximum is 40 m.
 
* The minimum level spreader length is 4 m and the maximum is 40 m.
* The level spreader lip should be concrete, wood or pre-fabricated metal, with a well anchored footer, or other accepted rigid, non-erodible material.
+
* The level spreader lip should be concrete, wood or pre-fabricated metal.
* The ends of the level spreader section should be tied back into the slope to avoid scouring around the ends of the level spreader; otherwise, short-circuiting of the facility could create erosion.
+
* The ends of the level spreader section should be tied back into the slope to avoid [[overflow]] scouring or erosion around the ends.
* The width of the level spreader channel on the up-stream side of the level lip should be three times the diameter of the inflow pipe, and the depth should be 20 cm or one-half the culvert diameter, whichever is greater.
+
* The width of the level spreader should be the greater of 300 mm or three times the diameter of the inflow pipe.
----
+
* The depth should be the greater of 200 mm or half the inflow pipe diameter.
 +
 
 +
==References==
 +
[[Category:Pretreatment]]

Latest revision as of 20:41, 27 September 2022

This clever design incorporates a level spreading device after a curb cut has narrowed the flow path. This kind of treatment train approach would provide an opportunity to provide pretreatment at the point of concentration. Photo credit: MPCA
Diagram from Wikimedia commons. Credit: U.S. Army Corps of Engineers, Construction Engineering Research Laboratory

Level spreaders should conform to the following design criteria in order to ensure non-erosive sheet flow into vegetated areas such as vegetated filter strips, bioretention, swales or forested conservation areas[1].

The length of the level spreader should be determined by the design storm inflow rate and type of landscape downstream:

  • 1.4 m of level spreader length per every 0.01 m³/s of inflow when draining to a vegetated filter strip, bioretention, swale or grassed area;
  • 4.3 m of level spreader length per every 0.01 m³/s of inflow when draining to a forested conservation area.
  • The minimum level spreader length is 4 m and the maximum is 40 m.
  • The level spreader lip should be concrete, wood or pre-fabricated metal.
  • The ends of the level spreader section should be tied back into the slope to avoid overflow scouring or erosion around the ends.
  • The width of the level spreader should be the greater of 300 mm or three times the diameter of the inflow pipe.
  • The depth should be the greater of 200 mm or half the inflow pipe diameter.

References[edit]

  1. Hathaway, J. M., & Hunt, W. F. (2006). Level Spreaders : Overview , Design , and Maintenance.